Sulfur content determination is a critical quality-control test for pyrolysis oils, gases, and solid residues derived from waste tires, plastics, and biomass. Accurate sulfur measurement directly affects fuel qualification, desulfurization process design, catalyst protection, and environmental compliance. This technical article reviews the sample types, testing items, analytical methods, and applicable international standards (ASTM, ISO, GB) used for sulfur determination in pyrolysis products.
Technical Overview
Pyrolysis is a thermochemical conversion process that decomposes carbonaceous feedstocks—such as waste tires, waste plastics, biomass, and oily sludge—into three product streams: pyrolysis oil (liquid), non-condensable pyrolysis gas, and solid char or recovered carbon black. Sulfur originally present in the feedstock is redistributed among these three phases during thermal decomposition, and its concentration in each stream has significant technical and regulatory consequences.
For example, vulcanized tire rubber typically contains 1.0–2.5 wt% sulfur from crosslinking agents, which results in tire pyrolysis oil (TPO) sulfur levels commonly between 0.3 and 2.0 wt%—far above the 10 mg/kg limit specified for automotive diesel in standards such as EN 590 and GB 19147. Biomass-derived bio-oil generally contains much lower sulfur, while plastic-derived oils vary depending on contaminant levels and sulfur-containing additives. Excess sulfur causes corrosion in downstream equipment, poisons hydrotreating and reforming catalysts, and generates SOx emissions upon combustion. Reliable sulfur determination is therefore essential for feedstock screening, process optimization, product certification, and emission accounting in pyrolysis-based recycling and refining operations.
Testing Samples
Liquid Pyrolysis Products
This category includes tire pyrolysis oil, plastic pyrolysis oil, biomass fast-pyrolysis bio-oil, and fractionated cuts such as pyrolysis naphtha, pyrolysis diesel, and heavy bottoms. Liquid samples are typically homogenized by shaking or gentle warming before analysis, and free water or suspended char particles must be removed or accounted for, as they can bias results in X-ray fluorescence methods.
Gaseous Pyrolysis Products
Non-condensable gases (NCG) consisting mainly of H2, CH4, CO, CO2, and light hydrocarbons may carry sulfur species such as hydrogen sulfide (H2S), carbonyl sulfide (COS), and mercaptans. Gas samples are collected in passivated sampling cylinders or Tedlar-type bags and analyzed promptly to avoid adsorption losses and oxidation artifacts.
Solid Pyrolysis Products
Solid residues include recovered carbon black (rCB) from tire pyrolysis, pyrolysis char, coke, and torrefied or carbonized biomass. Sulfur in these materials exists in multiple forms—elemental, sulfidic, and sulfatic—and the heterogeneous nature of chars requires grinding to a fine particle size (typically below 75 μm) and thorough mixing to obtain representative test portions.
Feedstock Materials
Feedstock samples such as shredded tire chips, plastic flakes, rice husk, or sludge cakes are analyzed to establish sulfur mass balance across the pyrolysis system, which helps operators predict sulfur partitioning into oil, gas, and char phases.
Testing Items
The core analytical offering for pyrolysis products typically includes the following determinations:
- Total sulfur content in pyrolysis oil, expressed in mg/kg or wt%
- Total sulfur in non-condensable gas, expressed in mg/m³ or mg/kg
- Hydrogen sulfide (H2S) and total mercaptan sulfur in gas streams
- Total sulfur, sulfide sulfur, and sulfate sulfur in recovered carbon black and char
- Total chlorine and sulfur simultaneously, when halogen interference must be characterized
- Feedstock sulfur for mass-balance and partitioning studies
Reporting typically includes the measured value, the applicable method standard, the detection limit, replicate precision, and any noted sample anomalies such as high water content or phase separation.
Testing Methods
Ultraviolet Fluorescence (UVF)
The sample is combusted at approximately 1050–1100 °C in an oxygen-rich atmosphere, converting all sulfur compounds to sulfur dioxide (SO2). The SO2 is excited by ultraviolet radiation, and the resulting fluorescence emission is quantified with a photomultiplier detector. Representative standards include ASTM D5453, ISO 20846, and SH/T 0689, with a working range from approximately 1 mg/kg up to several thousand mg/kg. This technique is the preferred choice for low-sulfur liquid products and distillate fractions destined for fuel blending.
Energy-Dispersive X-ray Fluorescence (EDXRF)
The sample is irradiated with X-rays, and the intensity of the sulfur Kα line at 2.3 keV is measured and compared against calibration standards. Standards include ASTM D4294, ISO 8754, and GB/T 17040, covering a typical range of 0.015–5.0 wt%. The method is fast, requires minimal sample preparation, and is well suited to process control, but matrix effects and spectral overlap from chlorine (a common co-contaminant in plastic-derived oils) must be corrected through matrix-matched calibration.
Wavelength-Dispersive X-ray Fluorescence (WDXRF)
Standards such as ASTM D2622 and GB/T 11140 employ crystal dispersion of characteristic X-rays, providing superior spectral resolution, better precision, and lower detection limits than EDXRF. WDXRF is appropriate when chlorine interference is significant or when certification-grade accuracy is required.
High-Temperature Combustion with Infrared Detection
The sample is burned in a resistance or induction furnace, and evolved SO2 is quantified by infrared absorption. ASTM D1552 applies to heavy petroleum products, while ASTM D4239 and related carbon-black procedures apply to coke, char, and recovered carbon black. This approach is robust for heterogeneous solids and high-sulfur materials.
Tube Furnace Method
The classical GB/T 387 procedure combusts the sample in a quartz tube furnace, absorbs the combustion products, and determines sulfur by iodometric titration. It remains a widely used reference method in Chinese laboratories for dark, heavy pyrolysis oils with elevated sulfur levels.
Oxidative Combustion Ion Chromatography (Combustion-IC)
Following ASTM D7359, the sample is combusted and the absorbed combustion gases are analyzed by ion chromatography, enabling simultaneous determination of sulfur and chlorine at low concentrations. This is particularly valuable for plastic-derived pyrolysis oils where halogen and sulfur contamination coexist.
Gas-Phase Sulfur Analysis
Total volatile sulfur in liquefied gases can be measured by UVF according to ASTM D6667, while speciation of H2S, mercaptans, COS, and other sulfur odorants is performed by gas chromatography with sulfur chemiluminescence detection (SCD), for example following ASTM D5504. Classical wet-chemical titration methods remain available for high-level H2S determination.
Method selection should follow these general guidelines:
- Low-sulfur liquid fuels and certification testing: UVF per ASTM D5453 or ISO 20846
- Rapid process screening of oils above ~150 mg/kg: EDXRF per ASTM D4294 or GB/T 17040
- Chlorine-containing plastic-derived oils: WDXRF or combustion-IC
- Char, coke, and recovered carbon black: combustion-IR per ASTM D4239 or ASTM D1619-based procedures
- Pyrolysis gas: UVF for total sulfur, GC-SCD for sulfur speciation
Quality assurance measures include matrix-matched calibration standards, certified reference materials (CRMs), procedural blanks, duplicate analyses with defined repeatability limits, spike recovery checks, and participation in interlaboratory comparison programs. Many producers and traders engage accredited third-party laboratories for independent verification of sulfur results.
Applications
Sulfur determination data support a wide range of industrial and regulatory applications:
- Desulfurization process development for tire pyrolysis oil, including oxidative desulfurization, hydrodesulfurization, adsorption, and extraction routes
- Qualification of pyrolysis fuels against specifications such as EN 590, GB 19147, and ISO 8217 for marine fuel blends
- Certification of recovered carbon black for reuse in rubber compounding, where sulfur form and content influence cure behavior
- Sulfur mass-balance studies to quantify partitioning into oil, gas, and char during reactor design and scale-up
- SOx emission inventories and environmental permit compliance for combustion of pyrolysis gas or oil
- Feedstock acceptance testing at chemical recycling plants to reject high-sulfur waste streams before processing
- Catalyst protection programs in downstream upgrading units, where sulfur poisoning thresholds must be respected
FAQ
Why is sulfur content in tire pyrolysis oil so high compared with standard diesel?
Tire rubber is vulcanized with elemental sulfur and sulfur-based accelerators, leaving roughly 1.0–2.5 wt% sulfur in the rubber matrix. During pyrolysis, a portion of this sulfur transfers to the oil phase, producing sulfur levels of 0.3–2.0 wt%, which is hundreds of times higher than the 10 mg/kg limit in automotive diesel specifications. This is why desulfurization is a mandatory upgrading step for TPO destined for fuel use.
Which method should I choose: ASTM D5453 or ASTM D4294?
ASTM D5453 (UVF) offers lower detection limits (down to about 1 mg/kg) and is preferred for compliance testing of low-sulfur fuels. ASTM D4294 (EDXRF) is faster and cheaper per test and is well suited for levels above approximately 150 mg/kg, making it ideal for in-process monitoring. For certification or dispute resolution, laboratories often confirm EDXRF results with a combustion-based method.
Does chlorine in plastic pyrolysis oil interfere with sulfur measurement?
Yes. In energy-dispersive XRF, the chlorine Kα line lies close to the sulfur signal and can bias results upward if not corrected. Wavelength-dispersive XRF or oxidative combustion methods such as UVF and combustion-IC are recommended when significant chlorine contamination is suspected.
How are heterogeneous solid samples such as char or recovered carbon black prepared?
Solid samples are dried, crushed, and ground to a particle size below approximately 75 μm, then thoroughly homogenized. Multiple test portions are analyzed to assess homogeneity, and results are reported as an average with repeatability information. High-temperature combustion with infrared detection is the most robust technique for these matrices.
How much sample is required for testing?
Typical minimum quantities are 20–50 mL for liquid pyrolysis products, 1–5 L (or an equivalent pressurized cylinder sample) for gas analysis, and 20–100 g for solid chars and recovered carbon black. Additional sample volume is recommended when replicate or confirmatory testing may be needed.
What detection limits can be achieved?
UVF methods routinely reach approximately 1 mg/kg for clean distillate fractions. EDXRF practical quantitation limits are typically in the range of 15–50 mg/kg depending on the instrument and matrix. Combustion-IR methods for solids generally quantify down to approximately 100 mg/kg (0.01 wt%). Actual limits of quantification should always be verified with the performing laboratory for the specific matrix.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing