Illuminance result determination is the systematic process of measuring and evaluating light levels on working surfaces using calibrated lux meters and standardized grid-based procedures. This article explains the core parameters, applicable standards such as GB/T 5700, ISO 8995-1, and EN 12464-1, sampling strategies, and calculation methods used by accredited third-party laboratories to verify that lighting installations meet design and regulatory requirements.
Technical Overview
Illuminance (E) is defined as the luminous flux incident on a surface per unit area, expressed in lux (lx), where one lux equals one lumen per square meter. Illuminance result determination refers to the complete measurement and evaluation workflow used to quantify the actual light levels delivered by a lighting installation and to compare them against specified design targets, national standards, or contractual acceptance criteria.
The determination process involves measuring illuminance at a defined grid of points on a reference plane (typically the horizontal working plane at 0.75 m above floor level for indoor environments, or the surface plane for outdoor areas), followed by the calculation of derived quantities such as average illuminance, minimum illuminance, and uniformity ratios. The results indicate whether an installation provides sufficient and evenly distributed light for the intended visual task.
Key standards governing illuminance measurement and evaluation include:
- GB/T 5700 – Measurement methods of illumination for lighting installations, specifying grid layout, instrument requirements, and measurement conditions.
- GB 50034 – Standard for lighting design of buildings, defining maintained illuminance and uniformity requirements for indoor workplaces.
- ISO 8995-1 / CIE S 008 – Lighting of work places, Part 1: Indoor, establishing illuminance levels for various task areas.
- EN 12464-1 – Light and lighting of work places, specifying required maintained illuminance and uniformity values.
- EN 13201 / CIE 140 – Road lighting performance requirements and calculation/measurement methods.
- JJG 211 – Verification regulation for illuminance meters (photometers), ensuring instrument accuracy classes.
Measurements must be performed with illuminance meters (lux meters) that match the photopic luminous efficiency function V(λ), provide cosine-corrected angular response, and hold valid calibration traceable to national metrology institutes. Instruments are classified into accuracy grades, and only meters of appropriate class should be used for compliance verification.
Testing Samples
Illuminance determination is applied to complete lighting installations rather than individual specimens. Typical measurement objects include:
Indoor Work Environments
Offices, classrooms, conference rooms, industrial workshops, inspection benches, and laboratories. The reference plane is generally the horizontal working plane 0.75 m above the floor, or the actual task surface where specified.
Public and Commercial Spaces
Corridors, staircases, lobbies, retail sales floors, warehouses, hospitals, and control rooms. Each functional area is measured and evaluated separately according to its designated task illuminance requirement.
Outdoor Lighting Installations
Roads and motorized traffic lanes, pedestrian and bicycle paths, parking areas, tunnel interiors, and building exteriors. Measurements are taken at points on the ground surface or road pavement under night-time conditions with daylight fully excluded.
Sports and Event Venues
Indoor gymnasiums, stadiums, tennis courts, and swimming facilities, where both horizontal illuminance on the playing surface and vertical illuminance toward fixed camera or spectator directions may be required.
Emergency and Safety Lighting Systems
Escape routes, open anti-panic areas, and high-risk task areas, where minimum illuminance levels under emergency supply conditions are verified against EN 1838 or equivalent requirements.
Testing Items
The principal quantities determined during an illuminance measurement program include:
- Average illuminance (Em) – the arithmetic mean of all point measurements across the defined grid, compared against the required maintained illuminance for the space.
- Minimum illuminance (Emin) – the lowest point value within the measurement area, identifying dim spots that may compromise visual performance or safety.
- Maximum illuminance (Emax) – the highest point value, used for uniformity and glare-related evaluations in certain applications.
- Illuminance uniformity (U0) – the ratio of minimum to average illuminance (Emin/Em), expressing the evenness of the light distribution over the area.
- Uniformity to minimum (U1) – the ratio of minimum to maximum illuminance (Emin/Emax), commonly specified for sports lighting and road lighting.
- Vertical and cylindrical illuminance – measured on vertical planes to assess face recognition, visual communication, and camera performance.
- Mixed and daylight contribution – where required, the electric lighting component is isolated by measuring with luminaires switched on and off to separate daylight influence.
Testing Methods
Illuminance determination follows a structured procedure to ensure reproducible, traceable results:
- Preparation and stabilization: Lamps and drivers should be sufficiently aged (typically at least 100 operating hours for new installations), luminaires and room surfaces cleaned, and the system operated for a stabilization period of 15 to 30 minutes before readings are taken so that light output reaches thermal equilibrium.
- Condition control: Indoor measurements are performed after dark or with daylight fully excluded (blackout) unless a mixed-lighting assessment is specifically required. For road lighting, measurements are taken at night with no traffic interference. Obstructions, reflective objects, and non-typical furniture that could shield or redirect light are documented or removed.
- Instrument selection: A calibrated illuminance meter of appropriate accuracy class is used, with the detector held parallel to the reference plane on a tripod or fixed support to avoid hand shadowing and reflection from the operator's clothing.
- Grid definition: The measurement area is divided into a rectangular grid according to GB/T 5700, EN 12464-1, or CIE guidance. The point spacing is selected so that the grid density captures meaningful variations—commonly requiring a minimum number of points that increases with room dimensions, and with grid cells approximately square. Measurement points are taken at the center of each cell.
- Reference plane: Readings are taken at the horizontal working plane (0.75 m above floor for seated tasks), at the floor for circulation areas, at the road surface for outdoor installations, or at task-oriented heights and orientations where the standard specifies.
- Data acquisition: At each grid point, the illuminance is recorded after the reading stabilizes. Multiple readings or time-averaged values may be taken where flicker or daylight fluctuation is present. The operator stands away from the detector to prevent body obstruction.
- Calculation of results: Average illuminance is computed as the mean of all point values. Uniformity U0 equals Emin divided by Em, and U1 equals Emin divided by Emax. Corrected results account for instrument calibration factors, lamp lumen depreciation assumptions, and maintenance factors where maintained values are reported.
- Evaluation and reporting: Results are compared with the applicable limits—for example, 300 lx with U0 ≥ 0.60 for standard office reading and writing tasks under GB 50034 and EN 12464-1, or task-specific values for fine assembly, inspection, and sports applications. The test report documents site conditions, instrument details and calibration certificate, grid layout, raw data, calculated parameters, uncertainty estimation, and a pass/fail conclusion against the referenced criteria.
Applications
Determined illuminance results serve a wide range of engineering, regulatory, and commercial purposes:
- Acceptance and commissioning: Verifying that newly installed lighting systems meet designer specifications and contract documents before handover.
- Regulatory compliance: Demonstrating conformity with workplace lighting standards, building codes, school hygiene regulations, and occupational health and safety requirements.
- Maintenance and relamping programs: Establishing baseline values and monitoring illuminance degradation over time to schedule cleaning, lamp replacement, or LED retrofit interventions.
- Energy audits and retrofits: Correlating measured illuminance with installed lighting power density (W/m²) to validate the efficiency and adequacy of energy-saving upgrades.
- Sports venue certification: Confirming that training, competition, and broadcast illuminance levels for various sport classes and competition grades are achieved.
- Road and tunnel lighting verification: Evaluating newly commissioned or renovated public lighting installations against specified average illuminance and uniformity thresholds.
- Dispute resolution and quality claims: Providing objective, traceable evidence in cases of lighting quality complaints, product performance disputes, or warranty assessments.
FAQ
What is the difference between illuminance and luminance? Illuminance measures how much light falls onto a surface in lux, while luminance measures how bright a surface appears to an observer in candela per square meter. Illuminance depends only on the incident light, whereas luminance also depends on the reflective properties of the surface.
At what height is illuminance measured? For general indoor workplaces, measurements are taken on a horizontal plane 0.75 m above the floor, representing a typical desk or task height. Circulation areas are measured at floor level, and special tasks may define their own reference planes and orientations.
How many measurement points are needed? The number of points depends on the size of the area and the applicable standard. GB/T 5700 and EN 12464-1 provide grid rules that increase point density with room dimensions so that no single cell dominates the average; a commonly applied target is that the grid divides the area into approximately square cells with no fewer than the minimum specified points.
Can measurements be taken during the day? For pure electric lighting assessment, daylight must be excluded by performing the test after dark or with blackout arrangements. If daylight contribution is intentionally part of the design, a mixed-lighting determination can be performed by measuring with luminaires on and off and subtracting the ambient component.
Why do measured values sometimes fall below design values? Common causes include lamp lumen depreciation, dirty luminaires and surfaces, non-compliant installation geometry, voltage deviations, or the absence of the maintenance factor assumptions used in design. A determination report identifies the shortfall and supports corrective action.
How often should illuminance be verified? Industry practice recommends periodic verification—typically annually or at intervals defined by the maintenance plan—so that cleaning and relamping can be scheduled before illuminance falls below the maintained values required by the applicable standard.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing